Custom Building Products Thin-Set Mortar Admix is a a liquid polymer designed to be used in place of water to increase performance of cement mortar beds, non-modified, thin-set mortars and cement-based grouts. It improves working characteristics and performance of cement-based mixes to boost water resistance, shock resistance and freeze-thaw capabilities for tile, stone or masonry installations. Increases performance of non-modified thin-set mortars for setting dense tile and setting over hard-to-bond surfaces. Thin-Set Mortar Admix can be used with non-modified, thin-set mortars such as, CustomBlend Thin-Set Mortar and Uncoupling Mat Mortar. It can also be used with Saltillo Grout Mix.

-Size: 2.5 gallon (9.46 L) bottle
-Pre-mixed, no diluting necessary
-A liquid polymer designed to be used in place of water to increase performance of cement mortar beds, non-modified, thin set mortars and cement based grouts
-Improves working characteristics and performance of cement based mixes to boost water resistance, shock resistance and freeze thaw capabilities for tile, stone or masonry installations
-Increases performance of non-modified thin set mortars for setting dense tile and setting over hard to bond surfaces.
-Suitable Tile Types
-Vitreous, semi-vitreous or non-vitreous tile: ceramic, mosaic, quarry, cement body tile
-Impervious porcelain and glass tile
-Brick and stone veneer
-Cement-based precast terrazzo
-Natural stone tile
-Suitable Substrates
-Concrete, mortar beds, masonry, Portland cement plaster
-WonderBoard, cement backerboards
-Liquid applied waterproofing membranes such as RedGard and Custom 9240
-Crack prevention sheet membranes such as Crack Buster Pro
-Exterior Grade Plywood (interior residential and light commercial dry areas)
-Gypsum wallboard (interior dry areas)
-Existing ceramic tile
-Fully-bonded sheet vinyl flooring
-Plastic laminates
-Cutback adhesive
-Composition and Materials
-Liquid Latex
Benefits:

-When mixed with non-modified thin-set mortars and mortar bed mixes:
-Improves bond strength
-Improves freeze-thaw durability
-Improves Flexibility
Increases performance for:

-Installation of hard-to-bond tiles
-Interior and exterior applications
-Limitations
-Do not bond directly to hardwood, Luan plywood, particle board, parquet, cushion or sponge-back vinyl flooring, metal, fiberglass, plastic or OSB panels.
-When setting moisture sensitive natural stone, cement or agglomerate tile use EBM-Lite Epoxy Bonding Mortar 100% Solids or CEG-Lite 100% Solids Commercial Epoxy Grout.
-Do not use to install resin-backed stone use EBM-Lite Epoxy Bonding Mortar 100% Solids, CEG-Lite 100% Solids Commercial Epoxy Grout or contact Custom’s Technical Services for recommendations.
-When setting glass tile larger than 6″ x 6″ (15 x 15 cm), contact Custom’s Technical Services for recommendations.
-When setting dimensional stone larger than 12″ x 12″ (30 x 30 cm), contact Custom’s Technical Services for recommendations regarding subfloor deflection requirements.
-Technical Data
-Applicable Standards

-American National Standards Institute (ANSI) ANSI A108.5; A118.4; A118.11 of the American National Standards for the Installation of Ceramic Tile Tile Council of North America (TCNA) TCNA Handbook for Ceramic Tile Installation, TCNA Method EJ171
-Environmental Consideration

-Custom Building Products is committed to environmental responsibility in both products produced and in manufacturing practices. Use of this product can contribute to LEED certification.
-Instructions
-General Surface Prep

-Surfaces must be structurally sound, clean, dry and free from grease, oil, dirt, curing compounds, sealers, adhesives or any other contaminant that would prevent a good bond. Glossy or painted surfaces must be sanded, stripped and cleaned of waxes, dirt or any contaminants. Concrete must be cured 28 days and accept water penetration. Concrete must be free of efflorescence and not subject to hydrostatic pressure. Concrete slabs should have a broomed or brushed finish to enhance the bond. Plywood flooring including those under resilient flooring must be structurally sound and meet all ANSI and deflection requirements. For questions about proper subfloor installation, call Technical Services. Smooth concrete surfaces, existing glazed tile, terrazzo, or polished stone should be roughened or scarified. Sheet vinyl must be-well bonded and stripped of old finish. Roughen the surface by sanding or scarifying, rinse and allow to dry. Expansion joints should never be bridged with setting material. Do not sand flooring materials containing asbestos. Ambient temperature, surfaces and materials should be maintained at a temperature above 50 F (10 C) or below 100 F (38 C) for 72 hours.
-Bonding to Cement Surfaces

-Concrete or plaster must be fully cured and must accept water penetration. Test by sprinkling water on various areas of the substrate. If water penetrates, then a good bond can be achieved; if water beads, surface contaminants are present, and loss of adhesion may occur. Contaminants should be mechanically removed before installation. Concrete must be free of efflorescence and not subject to hydrostatic pressure. Concrete slabs should have a broomed or brushed finish to enhance the bond. Smooth concrete slabs must be mechanically abraded to ensure a good bond.
-Bonding to Plywood Surfaces

-Plywood floors, including those under resilient flooring, must be structurally sound and must meet all ANSI A108.01 Part 3.4 requirements. See TCNA F150.
-Bonding to Backerboards

-Tile backerboards such as WonderBoard and are a superior alternative to using a second layer of plywood as a final substrate for tile installation. EasyMat is an underlayment that can be used in the same regard. Each provide unique benefits to tile installation but all can be installed over plywood to ensure that maximum bond strengths and performance are achieved. Refer to respective data sheet for installation information.
-Bonding to Existing Surfacing Material

-Plywood flooring must be structurally sound and meet all ANSI and deflection requirements. Resilient flooring or plastic laminates must be well-bonded, clean and free of all contaminates. Roughen the surface by sanding or scarifying, rinse and allow to dry. Do not sand flooring containing asbestos. For existing well-bonded ceramic tile, mechanically abrade with carborundum stone. Rinse and allow to dry. When sanding we recommend the use of an approved respirator.
-Bonding to Cutback Adhesive*Adhesive layers must be removed as they reduce mortar bond strength to cement surfaces. Use extreme caution as adhesives may contain asbestos fibers. Do not sand or grind adhesive residue, as harmful dust may result. Never use adhesive removers or solvents, as they soften the adhesive and may cause it to penetrate into the concrete. Adhesive residue must be wet-scraped to the finished surface of the concrete, leaving only the transparent staining from the glue. Do a test bond area first, to determine desirable results. Refer to the RFCI Pamphlet, “Recommended Work Practices for Removal of Resilient Floor Coverings\